EC200U-EUAA: need QuecPython firmware with IMS/VoLTE support

Module: EC200U-EUAA
Current firmware: EC200UEUAAR03A04M08_OCPU_QPY (package QPY_OCPU_V0005_EC200U_EUAA_FW from QuecDevZone)

On this build IMS is not available:
AT+COPS? → +COPS: 0,0,“vodafone.de”,7 (registered on LTE)
AT+CIREG? → +CIREG: 0,0
AT+CGDCONT? → only our data context (cid 1), no IMS context
AT+QCFG=“ims” → +CME ERROR: 3
AT+QCFG=“ims”,1 → +CME ERROR: 3

The SIM is VoLTE-capable on this network (verified).

Our application uses the QuecPython voiceCall API and needs voice calls over LTE (VoLTE), since 2G will be switched off in Germany.

Questions:

  1. Is there a QuecPython build for EC200U-EUAA with IMS/VoLTE enabled (comparable to EC200UCNAAR03A01M08_VOBT_OCPU_QPY for the CN variant)? Please send it or tell us where to download it.
  2. How is VoLTE enabled under QuecPython on that build - automatically, via an API call, or via an AT command?
  3. Is there a newer base than R03A04M08 for the EUAA QuecPython firmware?

See also: EC200A-EU: need QuecPython firmware with IMS/VoLTE support
Thank you.

1 Like

Dear customer

Could you share your email address with me? I will send the firmware that supports Volte to you for a try

Please store my email address and remove it from the forum (if possible) to protect me from spam.

ok, I got it. And I have sent the firmware to you. Please try it

Your email did in fact arrive but was held back by hornetsecurity. I could not yet read it, but thanks anyway.

Dear customer

I have uploaded the firmware to the server and resent it to you via email. Please give it a try.

Thank you for the new firmware EC200UEUAAR03A01M08_VOLTE_OCPU_QPY. IMS registration works: AT+CIREG? → +CIREG: 0,1,5 on Vodafone DE LTE.

However, the LTE band configuration of this build does not match the EC200U-EU variant:

AT+QCFG="band" -> +QCFG: "band",0xf,0x2000001a0080000df

Decoded (bit n-1 = band n), the LTE mask enables:
B1, B2, B3, B4, B5, B7, B8, B28, B38, B40, B41, B66

According to Quectel_EC200U_Series_LTE_Standard_Specification_V1.4, EC200U-EU supports LTE-FDD B1/B3/B5/B7/B8/B20/B28.

Differences:

  • B20 (800 MHz) is NOT enabled, although it is supported by EC200U-EU.
  • B2, B4 and B66 are enabled, although they are not listed for EC200U-EU (they are Americas bands).

I tried to enable B20 manually:

AT+QCFG=“band”,0xf,0x1a0080800d5,1 ? OK
AT+QCFG=“band” ? +QCFG: “band”,0xf,0x1a0080000d5

The command is accepted, B2/B4/B66 are removed as requested, but the B20 bit (0x80000) is silently dropped. So B20 seems to be not supported at all by this build, although the EC200U-EU datasheet lists it.

Please provide a EC200U-EUAA VoLTE QuecPython build with B20 support. In Germany B20 is often the only LTE band available indoors and in rural areas, so it is essential for our application.

Thank you.

Dear customer

I can reproduce you issue. let me confirm with the internal team

Dear customer

We’ve found the cause of the B20 issue. May I check if you are using single SIM or dual SIM?

We use only a single SIM, never dual SIMs

Dear customer

Please send this AT command

AT+QCFG=“band”,0xf,0x1a0080800d5

In my test, after I send this command, the module can support B20

image

Note:

This configuration will be saved once the command is sent. However, you will need to reconfigure it after reflashing the firmware.

CM_BAND_PREF_LTE_EUTRAN_BAND20 is 0x80000 and the output of your test at 10:56:38:764 shows that this is not available. Please check again.

In your test, the answer from EC200U was the same as in my test: +QCFG: “band”,0xf,0x1a0080000d5, showing that band 20 is not enabled.

Dear customer

Yes, you are right. I am very sorry. I made a mistake.
We are checking this issue.

Dear customer

May I ask do you need GNSS?

We do not need GNSS. Our devices are stationary.

ok, I got it. we have fixed this issue. Now I am applying for the firmware