How do I set 10Hz on the RMC message? I have set the rate to 10 and sent it but I only receive 1Hz.
B5 62 06 01 03 00 F0 04 0A 08 21
Dear Sir
Please provide the currently used module and firmware version (will be output when power is on).
Best Regards
Here is the information from powerup.
[11-24 16:25:48]$PQTMGNSS,0010C
[11-24 16:25:48]$PQTMVER,MODULE_LC29DANR01A01S_2WDR_HYF,2021/01/28,14:11:1712
[11-24 16:25:48]$PQTMVER,SUB_V033B
[11-24 16:25:48]$PQTMVER,QL_SDK_V1.1.3,2021/01/28,14:11:1758
[11-24 16:25:48]$PQTMSWCONFIG,1,1,17,55AA55AAC61BE69C000000000001FFFF00000000D9D8DA00640000000000000090D003000101640202010000010000000000000058595A00000000000000000011
[11-24 16:25:48]$PQTMSWCONFIG,1,2,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000013
[11-24 16:25:48]$PQTMSWCONFIG,1,3,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000012
[11-24 16:25:48]$PQTMSWCONFIG,1,4,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000015
[11-24 16:25:48]$PQTMSWCONFIG,1,5,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000014
[11-24 16:25:48]$PQTMSWCONFIG,1,6,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000017
[11-24 16:25:48]$PQTMSWCONFIG,1,7,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000016
[11-24 16:25:48]$PQTMSWCONFIG,1,8,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000019
[11-24 16:25:48]$PQTMSWCONFIG,1,9,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000018
[11-24 16:25:48]$PQTMSWCONFIG,1,10,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000020
[11-24 16:25:48]$PQTMSWCONFIG,1,11,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000021
[11-24 16:25:48]$PQTMSWCONFIG,1,12,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000022
[11-24 16:25:48]$PQTMSWCONFIG,1,13,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000023
[11-24 16:25:48]$PQTMSWCONFIG,1,14,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000024
[11-24 16:25:48]$PQTMSWCONFIG,1,15,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000025
[11-24 16:25:48]$PQTMSWCONFIG,1,16,17,0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000026
[11-24 16:25:48]$PQTMSWCONFIG,1,17,17,00000000000000000000000000000000000000000000000000000000000000000000000027
[11-24 16:25:50]$GNGNS,000001.00,NNNNNN,00,99.0,V18
[11-24 16:25:50]$GNRMC,000001.00,V,010712,N,V*1D
Dear Sir
This is the firmware of two-wheeled vehicles (scooters, electric vehicles, etc.), please refer to the attached application documents. NMEA RMC does not support 10Hz. If you need 10Hz, please refer to the INS sentence in the attached document to achieve it.
Best RegardsQuectel_LC29D_DR&RTK(0)_Application_Note_V1.0.pdf (295.9 KB)